Lead Test Technician

• 3rd Shift Prolec-GE Waukesha, Inc United States, North Carolina, Goldsboro Sep 02, 2026

About Company:

What Does Prolec GE Waukesha Do?

JOB SUMMARY

To perform a broad variety of tests on equipment and manufactured parts to determine if engineering standards, customer specification & IEEE standards have been met. Prolec GE Waukesha produces primarily 3 phase power step down transformers.

PRINCIPLE DUTIES AND RESPONSIBILITIES

Primary operating voltages range from 69kV to 230kV. This position encompasses performing the electrical tests to 1) verify the transformer controls: gauge, instrument and programmable controller operation and 2) transformer dielectric withstand and thermal capability. The controls testing involves employing VOMs and laptop computers to test circuit logic, instrument functionality and performance characteristics. The dielectric testing involves impulse testing to 1M V, Applied Potential testing >400kV, 3 phase 240Hz induced testing >100kV and 3 phase 60Hz performance testing. The test technician will follow blueprints, diagrams, downloads from manufacturer's web-sites and engineering specifications to set up and perform various test on equipment, manufactured parts and power supplies.

Interprets test data, identifies technical problem solutions and writes NCRs for quality problems during their assigned shift as well as the off shift.

Makes repairs on assigned test equipment as needed.

Performs the necessary test calculations and prepare data electronically as listed below to confirm test are complete and have produced acceptable results:

Turns Test

Ratio and Polarity

IEX and Core Loss

DC Resistance

Impedance and load loss

Induced and Applied Potential

Power Factor (INS)

Insulation Resistance

Heat run

• Connect
  Corona and Impulse
• Special
  SFRA (Sweep Frequency Response Analysis)
  BCT testing (standard & Omicron test set)
  Oil Quality testing
  Dew point testing
  Sound test
  Voltage and Current Regulator
• Special
  Electrical Inspection
  Final Mechanical Inspection
  Pressure Test Procedure
  Control Box checkout
• Special
  Top Cover checkout
  Final Inspection and Sign-off
  Fabrication Parts Inspection
  Current Trans.

Test

Calibrates Meters

Rejects non-conforming materials and assemblies

Calculates and analyzes the results of the test performed

Prepares charts and graphs to indicate process trends

Maintains a clean and safe work environment

Complies with all safety policies and procedures and actively participates in defined zero harm safety culture driven initiatives.

NOTE:

Must be able to satisfactorily perform a minimum 2 of the Special tests. May perform test in the presence of customers or their representatives during Witness testing.

KNOWLEDGE, SKILLS & ABILITIES TOOLS AND MACHINERY

Hand tools, ladders, electrical measuring meters, mechanical measuring devices, test equipment, system computer, and various computer controlled test equipment. Uses a variety of equipment to include impulse generator, Hi Pot, motor generator, power factor test kit, SFRA set, voltmeters, ammeters, watt meters, ohmmeters, bridges, oscilloscopes and wave analyzers to test a variety of equipment and manufactured parts.

MATERIALS

Arc flash clothing, electrically rated gloves GENERAL The successful candidate must be able to read electrical prints, technical requirements and industry standards. All testing parameters are predicated on the transformers design characteristics. The testing is not of the "plug in the wiring harness, push the start button and note the results" genre. It requires first and foremost a safety mindset as well as the ability to configure power supplies and generators and trouble shoot electrical problems. They must also obtain Arc flash training, follow safe electrical work practices, and take proper precautions to maintain arc flash boundaries for fellow testers and assemblers. Works under minimal supervision. Able to layout materials and setup for tasking. Work varies from working at ground level to working in, on top of, and around the sides of the unit, which may be 6 feet or more in height.

EDUCATION AND EXPERIENCE A BSEE

(or equivalent) is required with no experience, OR an AA degree in the electrical field with some related experience, OR high school diploma or GED with supplemental specialized electrical training and three years of experience OR high school diploma or GED plus 4 years of progressive experience in QA testing.

ADDITIONAL INFORMATION

The above description covers the principle functions of the job. It is not intended to be a complete listing of all the miscellaneous, incidental, or substantially similar duties, which may be assigned during normal or emergency operations. Prolec-GE Waukesha, Inc. is an equal opportunity employer and makes employment decisions without regard to race, color, religion, national origin, sex, sexual orientation, gender identity, age, genetic information, disability, protected veteran status, or any other reason prohibited by applicable law.