Job Summary We are seeking a motivated Diesel Mechanic to join our team. In this role, you will maintain, troubleshoot, and repair a diverse fleet of diesel equipment and trucks. Your expertise will be key to minimizing downtime and supporting our shop operations. If you thrive in a fast-paced environment where proactive problem-solving and hands-on skills are valued, this is a great opportunity to grow your career. Responsibilities Accurately document all repairs, labor hours, and parts used on work orders.

Dispatch & Response:

Respond promptly to service calls, emergency roadside breakdowns, and scheduled on-site customer maintenance.

On-Site Diagnostics:

Perform field-level troubleshooting on heavy diesel engines, aftertreatment/emissions systems, air brakes, and electrical systems using mobile diagnostic software.

Emergency Field Repairs:

Execute critical, safe, on-the-spot repairs—including air leak fixes, hose crimping/replacements, belt installs, hub seal repairs, and fuel priming—to minimize customer downtime.

Worksite Safety & Traffic Control:

Establish safe work zones on highways and job sites using high-visibility gear, service truck positioning, proper lockout/tagout, and environmental spill containment. Maintain a clean, organized, and safe work area in compliance with OSHA and shop safety standards. Operate shop equipment safely, including hoists, presses, torches, welders, and diagnostic tools. Troubleshoot, repair, and overhaul heavy-duty diesel engines and sub-assemblies. Repair and replace transmissions, clutches, driveshafts, differentials, and axle assemblies. Inspect, rebuild, and service hydraulic systems (pumps, hoses, valves, and cylinders) on equipment and trailers. Use diagnostic software (e.g., Cummins Insite, Detroit

DDDL, CAT ET

) to troubleshoot fault codes and mechanical failure. Trace and repair complex electrical issues, starting/charging systems, multiplex wiring, and lighting. Diagnose and service modern diesel exhaust/emissions systems (DPF, SCR, DEF, and EGR components). Perform routine preventative maintenance (PMs), including fluid/filter changes, grease jobs, and safety checks. Conduct thorough Certified DOT inspections and complete required compliance documentation. Inspect brake systems, steering mechanisms, suspensions, wheel ends, and tire conditions.

Skills Engine Rebuilding & Overhauls:

Skilled in performing in-frame and out-of-frame overhauls (piston/liner replacement, cylinder head work, setting valve lash, timing gear alignment).

Heavy Drivetrains:

Expertise in inspecting, servicing, and replacing heavy-duty manual/automated transmissions (Eaton, Allison, Detroit DT12), clutches, torque converters, drivelines, and differential assemblies.

Brakes & Suspensions:

Complete understanding of heavy-duty air brake systems (S-cam, air disc, ABS modules), steering linkages, kingpins, and heavy-duty leaf/air-ride suspensions.

Hydraulic Diagnostics:

Ability to read hydraulic schematics, test system pressures (PSI/flow), and rebuild/replace high-pressure pumps, valve banks, hoses, and cylinders.

Air Systems:

Servicing air compressors, governor valves, air dryers, and brake valves to ensure air-system integrity.

Software Diagnostics:

Hands-on experience with OEM software (Cummins Insite, Detroit

DDDL, CAT

ET, Volvo PTT, Wabco) to pull fault codes, run forced DPF regenerations, and monitor live parameters.

Electrical System Tracing:

Ability to read schematics and use a Digital Multimeter (DMM) to diagnose voltage drops, short circuits, sensor failures, and CAN-bus communication faults.

Aftertreatment & Emissions:

Deep technical knowledge of Tier 4 and modern road emissions systems, including EGR valves, DPF cleaning/rebuilding, SCR catalysts, and DEF dosing units.

Welding & Torch Work:

Proficiency in MIG (GMAW) and Stick (SMAW) welding for frame repairs, cross-member replacements, trailer floor grid repairs, and custom bracket fabrication.

Precision Machining & Fitting:

Operating manual lathes/mills, using precision tools (micrometers, dial indicators) to measure clearances, and executing thread repairs or bolt extractions.

Surface Prep & Refinishing:

Setting up abrasive sandblasting equipment and applying heavy-duty industrial coatings/primers using HVLP spray equipment.

DOT Compliance & Safety:

Thorough knowledge of Federal

DOT/CVSA

inspection criteria to ensure vehicles are safe and compliant before leaving the shop.

Problem-Solving & Efficiency:

Ability to systematically isolate mechanical failures quickly to minimize customer downtime.

Work Order Documentation:

Accurately logging diagnostic findings, parts used, labor hours, and specific repair procedures into shop management systems.

Independent Field Diagnostics:

Ability to systematically troubleshoot complex diesel, electrical, and hydraulic issues without immediate access to shop resources or lead technicians.

Emergency Roadside Repair:

Proficiency in performing quick, safe, and effective roadside repairs (e.g., air leaks, belt/hose failures, brake cage-outs, fuel system primes, and electrical bypasses) to get equipment moving or towed safely.

Field Safety & Worksite Control:

Knowledge of roadside safety protocols, setting up safe work zones (traffic cones, high-visibility positioning, lockout/tagout), and managing environmental risks (fluid containment).

Self-Sufficiency & Tooling:

Skill in utilizing mobile service truck equipment safely and effectively, including service cranes, engine-driven welders, high-output air compressors, and portable jump-pack/booster units. Don't meet every single requirement? Apply anyway! We value strong hands-on problem-solving skills and a solid work ethic. A Mechanic Certification or CDL is preferred, but not mandatory.

Pay:

$40,000.00 - $70,000.00 per year

Benefits:

401(k) 401(k) matching Employee discount Health insurance Paid time off Retirement plan People with a criminal record are encouraged to apply

Work Location:

In person