Authorized Inspector Position Available In Essex, Massachusetts

Authorized Inspector TUV SUD America United States, Massachusetts, Peabody Jun 12, 2025 Authorized Inspector

TUV SUD ARISE

is one of the largest providers of unbundled jurisdictional and shop inspection services in North America, and a global provider of ASME and National Board Post Construction inspection services.

POSITION SUMMARY

An ARISE Employee who holds a current and valid National Board Authorized Inspector Commission and has been designated as Authorized Inspector (AI) by

ARISE. JOB DESCRIPTION

The Authorized Inspector shall demonstrate the ability to perform shop and field (on-site) ASME/NB inspections to the satisfaction of the Agency employing him.

EXPERIENCE

Individuals for Authorized Inspector shall have met the experience criteria listed in RCI-1 Table 1, and the satisfactory completion of the National Board ” Construction Commission” course, hold a valid and current National Board Commission card. The individuals shall have attended the National Board course for Authorized Inspectors and received a passing grade on the Authorized Inspector exam given by the National Board. Individuals shall achieve a minimum of 80 hours on the job training in ASME shop/field fabrication and inspection under the supervision of a designated Authorized Inspector.

RESPONSIBILITIES

Recording daily inspections performed for verification, witness activities, and quality program monitoring activities in the Inspector Diary. Verifying the Certificate Holder has a valid Certificate of Authorization covering the scope of code activities to be performed at the location. Verifying the Certificate Holder has a valid Certificate of Authorization to register with the National Board, if the items are to be registered. Verifying that the Certificate Holder has the necessary

ASME BPV

Code Editions, Addenda, referenced standards, and code cases to cover the work planned.

• Monitoring the Certificate Holder’s accepted quality program on a continual basis.

Verifying that any revisions to the Certificate Holder’s quality program meet

ASME BPV

Code requirements before implementation. Notifying the Certificate Holder and the Authorized Inspector Supervisor, when appropriate of any nonconforming condition. Verifying that all applicable design drawings, specifications, and instructions for each job, including revisions, are complete and accurately reflect the

ASME BPV

Code requirements for the work to be performed. Verifying that design calculations for each job are complete and meet the requirements of the

ASME BPV

Code and the Certificate Holder’s quality program. The Authorized Inspector is not responsible for the accuracy of calculations. Verifying that design calculations for each job are on file and available for review. Verifying that only intended and identified material, as specified in the appropriate section of the

ASME BPV

Code, is used in code construction. Verifying that material is identified, documented, and remains traceable in accordance with the Certificate Holder’s quality program and

ASME BPV

Code requirements. Verifying

ASME BPV

Code-required documentation for material (partial data reports, material test reports, Certificate of Conformance) is available for review for each job.

The Authorized Inspector shall review material test reports, and/or other material documentation required by the

ASME BPV

Code to ensure

ASME BPV

Code compliance. Reviewing and accepting the method and extent of material defect repairs, prior to work being performed. Designating inspection points at stages of construction that will provide meaningful results to verify

ASME BPV

Code and quality program requirements are met. Performing inspections at designated inspection points. Performing internal inspections whenever access permits and when required by the

ASME BPV

Code. When access is not afforded based on design, the Authorized Inspector shall use other means to verify

ASME BPV

Code compliance. The use of mirrors or fiber optics should be considered. Performing all external inspections to verify

ASME BPV

Code compliance. Witnessing all pressure tests and proof tests as required by the

ASME BPV

Code. Verifying that welding/brazing procedure specifications, procedure qualification records, and welder/welding operator qualifications (including continuity records) are incompliance with

ASME BPV

Code requirements. Verifying welds are made using qualified procedures and qualified personnel. Verify that welders and welding operators are properly qualified for the welds begin performed. Verifying, as apc) Verifying, as appropriate, that the method and extent of weld repairs to welds and base material are in compliance with

ASME BPV

Code requirements. Verifying, as appropriate, that weld joint preparation is in compliance with design and welding documents and

ASME BPV

Code requirements. Verifying completed welds comply with

ASME BPV

Code requirements. Verifying that only calibrated examination, measurement, and testing equipment are utilized during construction and that such equipment meets the requirements of the Certificate Holder’s quality program. Verifying all

ASME BPV

Code-required heat treatment and nondestructive examinations are performed using accepted/approved procedures. Nondestructive examination procedures shall be demonstrated to the satisfaction of the Authorized Inspector. Verifying nondestructive examination personnel are qualified as required by

ASME BPV

Code and the Certificate Holder’s quality program. Verifying nondestructive examination reports meet

ASME BPV

Code requirements. Reviewing and accepting non-conformance dispositions and verifying corrective actions performed. Also, verifying non-conformances are closed in accordance with the Certificate Holder’s quality program. Verifying all records are complete, accurate, maintained, and retained as required by

ASME BPV

Code and the Certificate Holder’s quality program. Verifying the Certificate Holder’s representative has accurately completed and certified the Manufacturer’s Data Report form prior to Authorized Inspector certification. The Authorized Inspector’s Commission number shall be recorded on the Manufacturer’s Data Report as required by the applicable

ASME BPV

Code. Verifying all

ASME BPV

Code requirements have been met before authorizing

ASME BPV

Code symbol stamping. Verifying the stamping meets

ASME BPV

Code, is correct, and has been applied to the correct item, including proper attachment of nameplates. Verifying the National Board NB symbol and National Board registration number are applied to any item registered with the National Board. The Authorized Inspector shall attend joint reviews of Certificate Holders to which the Authorized Inspector is assigned. When this is not possible or practicable, a substitute Authorized Inspector shall attend. It is not required for the Authorized Inspector to attend joint reviews of organizations that are inactive if the assigned Authorized Inspector Supervisor is in attendance. An inactive organization is one that has not used its ASME Certificate of Authorization during the previous certification period.

SKILL SET

• Detail oriented
• Manages time efficiently
• Works effectively with other people as necessary.
• Self-starter
• Represent ARISE products and services in a professional manner.
• Ability to meet deadlines.
• Excellent communication skills; oral and written
• Innovative Equal Opportunity Employer – Disability and Veteran TUV SUD America, Inc.

is an equal opportunity, affirmative action employer and considers qualified applicants for employment without regard to race, color, creed, religion, ancestry, marital status, genetics, national origin, sex, sexual orientation, gender identity and expression, age, physical or mental disability, veteran status and those laws, directives, and regulations of Federal, State, and Local governing bodies or agencies. We participate in the E-Verify Employment Verification Program. For more information on applicable equal employment regulations, please refer to the following: Details
Employment type Part time / permanent Work model remote Job location Home Office Country United States Job category Other Target Groups Required experience Professionals 3 – 5 years of experience Organizational unit
Reference number 140784 Contact TUV SUD Recruiting 1-800-888-0123careers.us@tuvsud.com
Apply nowPrintAdd to my favorites
Share
About TUV SUD as Employer At TUV SUD we are passionate about technology. Innovations impact our daily lives in countless ways, and we are dedicated to being a part of that progress. We test, we audit, we inspect, we advise. We never stop challenging ourselves for the safety of society and its people. We breathe technology, we strive for professional excellence, and we leave a mark. We take the future into our hands. We are TUV SUD. Established more than 150 years ago in Germany, TUV SUD is a leading global provider of technical services with more than 28,000 highly skilled employees across 1,000 offices worldwide. For over 30 years, throughout 33 locations, it is TUV SUD America’s priority to create a safer future. To protect people, property and the environment from technology-related risks; we drive consumer protection, digital transformation, sustainable development, and urbanization. Find out more about TUV SUD